Item Numbers in Red are hazardous items in blue are new v oversized d ups/fedex Surcharge u - WARNING Cancer Causing See www.P65Warnings.ca.gov v - WARNING Reproductive Harm w - WARNING Cancer and Reproductive Harm Awnings & Accessories Campsite Living General Accessories Roofing & Sealants Sanitation Heating & Cooling Grilling & Campware Housewares Cleaners & Waxes Fresh Water Generator & Power Solutions Appliances Lighting Hardware Service & Maintenance Steps & Tiedowns Towing & Hitches Electrical Electronics Vents Carriers & Covers Jacks & Levelers LP Gas 507 Lighting Item# Size Case List 590-1165w 16" x 1.5" x 1.625" 12 20.29 EA • Meets the requirements of SAE/DOT/FMVSS/CMVSS standards when properly installed • Sonically sealed, waterproof • Polycarbonate lens and housing • Design includes both lead and ground wire LED SEALED IDENTIFICATION LIGHT BAR Item# Size Case List 590-1166w 14.25" W x 1.188" H x 1.313" D 6 28.59 EA • Meets the requirements of SAE/DOT/FMVSS/CMVSS standards when properly installed • Designed for Over 80" Wide Trucks/Trailers • Waterproof • 9 LED lights • Single wire • Grounds through mounting hardware • Stainless steel base LED SEALED 3-PIECE IDENTIFICATION LIGHT BAR Light bar with three waterproof red lights. Stainless base with stud mounting. Item# Description Size List 274-401567w Waterproof Bar (Packaged) 14 1/4" x 1 3/16" x 1 1/16 67.49 EA WATERPROOF LED ID LIGHT BAR Item# Description List 177-416Kw Clear kit 23.29 BG Sealed, oval back-up light meets DOT requirements in either horizontal or vertical position. Polycarbonate lens is sonic welded to housing to form single unit. Requires mounting grommet and 2-wire plug to complete installations. Kit includes light, grommet, and right angle plug. 12-volt lamps designed with single filament, 2.1 amp, 32 cp bulb. BACK UP LIGHT KIT Item# List 681-DG52437VP 65.99 EA Weatherproof 6" Back Up LED Light Kit - 45 diode. Mount vertically or horizontally. Kit includes grommet and plug. 6 1/2"L x 2 1/4"W x 1 1/2"D. WEATHERPROOF 6" BACK UP KIT Item# Size Case List 590-1157w 3 1/4" x 3 1/4" x 13/16" 6 21.69 EA • 9 White LEDs • Designed to illuminate hitch area • Sonically sealed & waterproof • Flange surface mount - no panel cutout required • Design includes both lead and ground wire • Polycarbonate lens and housing • 12.8VDC - 0.074A LED 3" SEALED UTILITY/HITCH LIGHT Item# List 158-TL21RKw 66.39 EA Magnet mount towing light kit with 20-ft. wiring harness plugs into standard 4-wire flat vehicle connector. Ideal for safely marking any vehicle towed behind an RV or another vehicle. MAGNET MOUNT TOWING LIGHT KIT Item# List 158-TL22RKw 69.99 EA Includes a pair of DOT compliant stop/turn/tail lights. 20' Wishbone style wiring harness and 4-ft trunk connector with 4-way flat plug. Acrylic lens and plastic housing. Replaceable lens and bulb. MAGNETIC MOUNT TOWING LIGHT KIT Item# Size Pack Bulb Case List 50-52951w 2" x 18" 4 Incandescent 12 11.01 EA • Complies with J1967 for vehicle conspicuity material, as well as meeting all D.O.T. requirements • Rated at over 600 candlepower per square foot • Hermetically sealed and unbreakable • Mounts on flat or curved surfaces • Not to replace legally required reflector REFLECTIVE TAPE KIT Item# Size Pack Case List 177-465Kv 2" W x 18" L 8 12 29.39 PK High-brightness, red & white reflective material is rated at 1,000 candlepower and features industrial-strength adhesive to mount on flat or curved surfaces. It also offers: four-times greater reflectivity, wider viewing angles, higher visibility at long range and tougher durability than conventional conspicuity reflectors. REFLECTIVE MARKING TAPE License Plate Brackets & Accessories Item# Case List 590-1030 12 2.39 EA • Black heavy duty plastic, corrosion-proof • Universal Application • Meets the requirements of SAE/DOT/FMVSS/CMVSS standards when properly installed This Universal License Plate Bracket must be installed on the rear of the vehicle or trailer. LICENSE PLATE BRACKET Item# Description List 177-V438w Clear Lens, Viz Pack 7.99 EA • Chrome plated steel light snaps into 1 1/4" diameter hole (overall diameter is 1 1/2") • Commonly used to illuminate license plate on step bumpers • Two units required for legal license illumination • Also serves as perfect interior, compartment, courtesy, or general illumination utility light • 438 Series is sealed with single 6' lead wire CHROME LICENSE PLATE/UTILITY LIGHT Item# Size Case List 177-V44009w 8" x 2 3/4" 24 3.59 EA Tough molded, flexible plastic material. Will not rust or corrode. Allows bracket and license plate to deflect on impact-returns to original position. Designed for use with all Anderson rear lights. LICENSE BRACKET Item# Size Case List 177-42809w 8 1/2" x 2 3/4" 24 6.29 EA Zinc plated steel slotted for universal mounting. UNIVERSAL LICENSE BRACKET Item# Description List 220-3472100 Bracket 13.99 EA Stamped from heavy gauge steel and zinc plated. LICENSE PLATE BRACKET
RkJQdWJsaXNoZXIy MTI2MTky