GENERAL BOATING WATERSPORTS & BOATS SEATING COVERS/TOPS MAINTENANCE ELECTRICAL HARDWARE PLUMBING PROPS & ANODES FUEL ELECTRONICS & NAVIGATION SAFETY TROLLING & FISHING ANCHORING/ MOORING TRAILERING PAINT VENTILATION FASTENERS STEERING ENGINE ITEMS ARE STOCKED IN OUR WAREHOUSES BASED ON REGIONAL DEMAND. IF AN ITEM IS NOT IN STOCK AT A LOCAL WAREHOUSE, ADDITIONAL CHARGES MAY APPLY. u - WARNING Cancer Causing See www.P65Warnings.ca.gov v - WARNING Reproductive Harm w - WARNING Cancer and Reproductive Harm 472 SECTION ANCHORING/MOORING Item# Description List 241-26521a(K) Standard Grade 66.39 EA 241-26400a(KW) Commercial Grade 78.99 EA A. Two 1/ 2" welded tabs. Use with a male outside corner. Each leg is 10"L x 5"H. A. OUTSIDE CORNER (FEMALE) 26522 B. Use with a female outside corner to connect docks end to end. Joint requires 3/ 4" bolt set (N) or connector pin (O). Each leg is 10"L x 5" H. B. OUTSIDE CORNER (MALE) Item# Description Size List 241-26522a(KW) Standard Grade 1/ 2" Welded Tab 59.69 EA 241-25491a(LK) Commercial Grade 1/ 2" Welded Tab 63.99 EA 241-26418a(LK) Commercial Grade 3/ 4" Welded Tab 72.99 EA 26523 C. Use this corner at ends of fingers and docks. Ideal for swim floats and ski jump corners. C. OUTSIDE CORNER END Item# Description Size List 241-26523a(K) Standard Grade Each leg is 10"L x 5"H 32.99 EA 241-26402a(KW) Commercial Grade Each leg is 10"L x 5"H 47.99 EA 241-26428a(KW) Commercial Grade Each leg is 121/ 4"L x 5"H 70.49 EA Item# Description Size List 241-26524a(LK) Standard Grade 81/ 4"L x 5"H w/ 2" holes 36.59 EA 241-26403a(LK) Commercial Grade 81/ 4"L x 5"H w/ 21/ 4" holes 54.79 EA 241-26417a(KW) Commercial Grade 81/ 4"L x 5"H w/ 3" holes 55.49 EA 241-26401a(KW) Commercial Grade 81/ 4"L x 5"H w/ Square holes 48.79 EA 241-26424a Commercial Grade 101/ 2"L x 5"H w/ 21/ 4" holes & larger brace 60.69 EA D. Should be used with one of the outside corners. Each leg has elongated holes for easy fit. D. INSIDE CORNER E. Should be used with one of the outside corners and has an internal pipe holder. 81/ 4"L x 5"H. Requires carriage bolt set "M" for attaching. E. INSIDE CORNER / PIPE HOLDER Item# Description Pipe List 241-26404a(K) Commercial Grade 3" 118.29 EA F. Should be used for all cross supports. F. ANGLE Item# Description Size List 241-26527a(K) Standard Grade Each leg 21/ 2"L x 5"H 11.49 EA 241-26399a(LK) Commercial Grade Each leg 21/ 2"L x 21/ 2"H" 10.19 EA 241-26406a(K) Commercial Grade Each leg 21/ 2"L x 5"H 13.29 EA 241-26392a(K) Commercial Grade Each leg 23/ 4"L x 21/ 2"H 10.19 EA 241-26422a(LK) Commercial Grade Each leg 23/ 4"L x 5"H 10.79 EA 241-26398a(K) Commercial Grade Each leg 3"L x 5"H 17.69 EA 241-26380a(K) Commercial Grade Each leg 4"L x 7"H" 24.79 EA 241-26397a(K) Commercial Grade Each leg 4"L x 8"H 31.69 EA G. Bolts to side of dock to attach fingers and ramps. G. FEMALE T CONNECTOR Item# Description Size List 241-26528a(KW) Standard Grade w/ 1/ 2" tabs 5" x 5" 41.79 EA 241-26407a(KW) Commercial Grade w/ 1/ 2" tabs 5" x 5" 49.09 EA H. Use with Female T connector to attach fingers and ramps. Bolt set "N" required for joint. H. MALE T CONNECTOR Item# Description Size List 241-26532a Standard Grade w/ 1/ 2" tab 5" x 5" 32.59 EA 241-26408a(KW) Commercial Grade w/ 1/ 2" tab 5" x 5" 35.69 EA 241-26427a(K) Commercial Grade w/ 3/ 4" tab 5" x 5" 42.99 EA I. Should be used with every Angle. Two required for each Angle. 11/ 2"L x 5"H. I. WASHER PLATE Item# Description List 241-24284a(K) Standard Grade 6.29 EA 241-26409a(KW) Commercial Grade 5.19 EA
RkJQdWJsaXNoZXIy MTI2MTky