GENERAL BOATING WATERSPORTS & BOATS SEATING COVERS/TOPS MAINTENANCE ELECTRICAL HARDWARE PLUMBING PROPS & ANODES FUEL ELECTRONICS & NAVIGATION SAFETY TROLLING & FISHING ANCHORING/ MOORING TRAILERING PAINT VENTILATION FASTENERS STEERING ENGINE ITEM NUMBERS IN RED ARE HAZARDOUS ITEMS IN BLUE ARE NEW ] SEA VALUE v OVERSIZED d UPS/FEDEX SURCHARGE (L) = SE & MIDWEST ONLY (K) = NE & MID-ATLANTIC ONLY (W) = WEST COAST ONLY u - WARNING Cancer Causing See www.P65Warnings.ca.gov v - WARNING Reproductive Harm w - WARNING Cancer and Reproductive Harm SECTION 1421 ENGINE Outboard Motor Mounting Plates Item# Max Load Rating List 781-550405 263 lbs 35 hp 261.09 EA Makes mounting most auxiliary and long shaft motors a snap. When direct transom mounting is difficult, it provides a flat, secure mounting surface for clamps or bolt-on. Solid cast aluminum with an 8" x 7" mounting area, it can be used on most contoured transoms. By MarineTech TM STATIC MOTOR MOUNT PLATE Outboard Motor Transom Pads/Support Plates Item# Description Size List 119-20022c(LK) Upper plate Hole centers 127/ 8" 62.29 EA 119-20032c(LK) Lower plate Hole centers 97/ 8" 55.79 EA Made of strong 3/ 8" 6061 T6 alloy aluminum (not cast aluminum), these transom plates eliminates bolts "biting" into transoms and can more evenly distribute loads on high performance engines. TRANSOM SUPPORT/WASHER PLATES Item# Fits List 114-09907310c Most outboards to 25HP 38.49 EA Rubber pad is oil and weather resistant. Reduces motor vibration noise. Protects transom. Measures 11" W x 14.75" L x 6.86" wide at bottom. ENHANCED RUBBER TRANSOM PAD Item# Size List 781-559100 15"L x 21/ 8"W x 1/ 2"D 63.49 EA Made from heavy duty 713 cast aluminum, chromate dipped and black powder coated. Will add support for your transom when mounting your main or auxiliary motors. By MarineTech TM MOTOR MOUNT BOLT BAR Item# Size List 169-1780223c(LK) 2" x 15" 70.39 EA 169-1780203c(LK) 4" x 17" 77.89 EA Adds strength to boat's transom by evenly distributing forces during fast starts, high speed runs and sharp turns. Quality cast in Almag 35 aluminum for non-corrosive strength. Black. 12" bolt pattern. TRANSOM TUFF'NER™ SUPPORT PLATE Item# Description List 232-TSP1DP]c 13" Bolt Hole Pattern 39.19 EA 232-TSP2DP]c 10" Bolt Hole Pattern 32.59 EA • Distributes the stress of the motor mounting bolts • High quality cast aluminum • 3/ 8" thickness TRANSOM SUPPORT PLATE Outboard Motor Locks Item# Finish List 220-OML0127]c Black Powder Coat 58.49 EA Mounts over outboard mounting clamp handles. Made of heavy gauge steel with long lasting black powder-coat finish for years of protection against rust and corrosion. Foam filler insert reduces noise and vibration. Mounts on most outboard motors. OUTBOARD MOTOR LOCK Stainless Steel Finish. Designed to lock the outboard onto the transom, simply replace one of the mounting nuts with a McGard locking nut. A free spinning collar turns if attacked by gripping tools, protecting against theft and inconvenience. (74049 fits most of the motors listed and will fit other small outboards with a 5/ 16" hole in the transom bracket for mounting the motor.) OUTBOARD LOCK Item# Description List 371-74036]c 1/2-20 Merc/Mariner 40+ hp (2-stroke), Merc 25+ hp (4-stroke), Suzuki 150-300 hp 52.59 EA 371-74037c M12 x 1.25 Yamaha 40+ hp (2-stroke), 30+ hp (4-stroke), Honda 40+ hp, Suzuki 25-140 hp (2005 & newer) 52.59 EA 371-74038c 1/2-13 Johnson/Evinrude 40+ hp (2-stroke) 52.59 EA 371-74049c 5/16-18 Honda 8-30 hp, Johnson/Evinrude 6-30 hp, Merc/Mariner 8-25 hp, Nissan 8-18 hp, Suzuki 8-30 hp, Tohatsu 8-18 hp, Yamaha 8-25 hp. May fit other 2-strokes up to 30 hp with 5/16-18 bolts. 52.59 EA • 3.22" overall length • M10 x 1.25 thread size • 5/ 8" hex size • Set includes lock bolt and key Designed for Yamaha lower units, we feature a SS locking bolt. Simply replace one of the original bolts above the propeller with a McGard locking bolt. Once installed, the lower unit lock bolt offers 24 hour protection. Constructed of through-hardened stainless for maximum security. A free-spinning collar will turn if attacked by gripping tools without loosening the lock. For maximum security, use in conjunction with a Yamaha lower unit lock bolt. OUTBOARD LOWER UNIT LOCK SET Item# Description Finish List 371-74059c(LW) Fits: Yamaha F/LF115 - F/LF350 L & X Shaft Motors (*except F150 X shaft). Also most Yamaha V4 & V6 2-Strokes Stainless 77.79 EA Item# Description Finish List 371-74018]c Single Stern Drive Stainless 50.89 EA 371-74019c Twin Stern Drive Stainless 73.99 EA Simply replace one of the sterndrive mounting nuts for theft protection. Stainless steel with free-spinning collar that will turn if attacked by gripping tools. No assembly required. Fits Mercruiser® Alpha, Bravo I-III (Incl. X & XR), Blackhawk, OMC Cobra & King Cobra, and Volvo SX & DP-S stern drives. Carded for pegboard or for P.O.P. merchandiser. 74019 twin drive set includes 2 locks and 1 key. STERN DRIVE LOCK Item# Finish List 781-758101 Stainless 67.69 EA This high security lock is designed for bolt on engines. It is made from polished 300 series marine grade stainless steel, features anti drill protection and includes 2 keys which cannot be duplicated without the 4 digit key code provided. Fits up to 1/ 2" engine bolts. By MarineTech TM STAINLESS STEEL OUTBOARD BOLT-ON LOCK
RkJQdWJsaXNoZXIy MTI2MTky