GENERAL BOATING WATERSPORTS & BOATS SEATING COVERS/TOPS MAINTENANCE ELECTRICAL HARDWARE PLUMBING PROPS & ANODES FUEL ELECTRONICS & NAVIGATION SAFETY TROLLING & FISHING ANCHORING/ MOORING TRAILERING PAINT VENTILATION FASTENERS STEERING ENGINE ITEM NUMBERS IN RED ARE HAZARDOUS ITEMS IN BLUE ARE NEW ] SEA VALUE v OVERSIZED d UPS/FEDEX SURCHARGE (L) = SE & MIDWEST ONLY (K) = NE & MID-ATLANTIC ONLY (W) = WEST COAST ONLY u - WARNING Cancer Causing See www.P65Warnings.ca.gov v - WARNING Reproductive Harm w - WARNING Cancer and Reproductive Harm ELECTRONICS 129 Ratchet mount antenna bracket with handle, for side or deck mounting. Investment cast 316 stainless steel construction with dual swiveling mounts for full adjustability. This bracket will accept any standard antenna with 1"-14 threads. Designed with an integral feed system for Loran cable. Installs with four ¼" FH fasteners not included. ADJUSTABLE ANTENNA BASE Item# A B C D E Case List 354-3292301 41/ 2" 21/ 2" 35/ 8" 113/ 16" 215/ 16" 5 94.95 EA Investment Cast 316 Stainless Steel. For use with over-height whips or where extra strength and rigidity are required. Dual swiveling mounts allow for complete adjustability. Accepts any standard antenna with 1"- 14 threads. HEAVY DUTY ADJUSTABLE ANTENNA BASE Item# A B C D E Fastener List 354-3292351 515/ 16" 21/ 4" 33/ 4" 11/ 2" 3" 1/ 4" FH 97.95 EA Item# Material List 167-4186Ua Solid Nylon 24.59 EA Opt. Accy. Description List 167-414a Shim Kit 15.49 EA Solid nylon with handle for deck or bulkhead mounting. 1"-14 male thread. Not for antennas longer than 8' in selfsupporting mode-will nullify all warranties. 4186-U 4-WAY RATCHET MOUNT Item# Material List 167-4186BPa Solid Nylon 25.49 EA Opt. Accy. Description List 167-414a Shim Kit 15.49 EA For deck or side mounting. Quick action handle makes operation easy. Bolt holes: 5/ 16" dia., 3" x 11/ 2" on center. Not for use with antenna longer than 8' in self-supporting mode. NYLON 4-WAY RATCHET MOUNT Sleek, four-way ratchet mount with a nutless design. Has standard 1"-14 threads and a special cable slot that eliminates removal of most factory installed connectors. Easy on the eye, and super easy to use. 5º Teeth for finer adjustments than standard mounts. • Standard 1"-14 thread (male) • Slot for cable feed-through • Bolt holes: 5/ 16" Dia., 3" x 11/ 2" on center 5187 STAINLESS STEEL CUSTOM LOOK 4 WAY RATCHET MOUNT Item# Material List 167-5187a Stainless Steel 93.99 EA Item# Material List 167-6187a Stainless Steel 166.89 EA Full 4D range of motion with no tools. Maximum mounting flexibility - deck or side mount, even at extreme angles. Standard 1"-14 threads. Bolt holes: 5/ 16" diameter 3" x 11/ 2" on center. STAINLESS STEEL RATCHET MOUNT Item# Description List 167-4187]a Standard Duty 94.69 EA 167-4187HD]a Heavy Duty 109.19 EA Opt. Accy. Description List 167-414a Shim Kit 15.49 EA Versatile four-way ratchet design for deck or side mounting. Quick-action handle makes operation easy. • Stainless Steel • Bolt holes: 5/ 16" Dia., 3" x 11/ 2" on center • Standard 1"-14 thread (male) • 9/ 32" hole for cable feed-through STAINLESS STEEL STANDARD 4-WAY RATCHET MOUNT Item# Description Material List 167-QCMNc For Quick Connect antennas up to 4' White Nylon 63.29 EA 167-QCMS]a For Quick Connect antennas up to 8' Stainless Steel 117.39 EA • Standard 1" -14 thread • Bolt holes: 9/ 32", 3" x ½" on center • Water and dust protection cap, stays fastened to mount • PL-259 Connector & 20'RG-58 coax cable included To be used with QuickConnect® antennas only. Versatile four-way ratchet action and fast-release handle design for quick and easy laydown. For deck or side mounting of QuickConnect® antennas. QCM - QUICKCONNECT® RATCHET MOUNT Nylon Stainless Item# Description List 167-414a Shim Kit 15.49 EA Fits #4186 and 4187 5deg. Tilt contains 2-front-to-back and 2-side-to-side shims. SHIM KIT Item# List 236-GS8001](LK) 660.59 EA • No climbing on T-tops or gunnels • Standard 1"-14 thread (male) • Machined / Anodized aluminum body • Light brushed finish • Polished Type-316L stainless folding crank handle • Delrin bearings for smooth operation • Roller bearings in crank assembly • Mounts on hardtops up to 2" thick • Includes 4" x 1/ 4" round backing plate (hardware not included) • Made in the USA • 1-year limited warranty Created specifically to prevent climbing on the boat gunnel to raise and lower a VHF antenna. Lift and descend the antenna from the safety of the deck from under the top. Its smooth operation, attractive machined aluminum frame and cast stainless-steel rotator make this item a must for any boater. GRAND SLAM VHF ANTENNA MOUNT
RkJQdWJsaXNoZXIy MTI2MTky