GENERAL BOATING WATERSPORTS & BOATS SEATING COVERS/TOPS MAINTENANCE ELECTRICAL HARDWARE PLUMBING PROPS & ANODES FUEL ELECTRONICS & NAVIGATION SAFETY TROLLING & FISHING ANCHORING/ MOORING TRAILERING PAINT VENTILATION FASTENERS STEERING ENGINE ITEMS ARE STOCKED IN OUR WAREHOUSES BASED ON REGIONAL DEMAND. IF AN ITEM IS NOT IN STOCK AT A LOCAL WAREHOUSE, ADDITIONAL CHARGES MAY APPLY. u - WARNING Cancer Causing See www.P65Warnings.ca.gov v - WARNING Reproductive Harm w - WARNING Cancer and Reproductive Harm 1280 SECTION STEERING Seastar Solutions Baystar Systems Item# Includes List 1-HK43004]c HH43144 Std Helm w/o Tubing 1099.89 EA • Requires 5" H x 6" D x 21" W minimum splashwell • 5 Turns lock-to-lock • Balanced cylinder fits most splashwells • 5" footprint; needs only 3" hole (Standard or Tilt) • Complete with helm, cylinder, fittings, tubing, oil, fill kit & instructions • Standard 3/ 4" tapered shaft • Meets A.B.Y.C. standards and meets NMMA certification requirements Kits Includes: • BayStar Helm 1.4 cu with adjustable O-ring fittings • HC4645H3 - BayStar Compact Cylinder • HA5430 (2) - Hydraulic Oil (1 liter) • HT4420H - (2) 20' hoses (on select kits) Application: BayStar is for single-outboard powered boats rated up to 150 HP, including runabouts and inflatables and outboard engines with ABYC standard engine tilt tubes up to 150 HP (total). For single station, single engine use only. BayStar is not intended for high speed, high performance type boats. Helm and cylinder equipped with adjustable O-ring fittings to simplify the installation process and allow for simple reorientation of the fittings after installation. Two year warranty. BAYSTAR COMPACT HYDRAULIC STEERING SYSTEM Tiller Rope Steering Parts Item# Qty Case List 50-28501c 2 12 13.99 PK Pair of stainless steel and plastic pulleys with two stamped stainless steel eye straps. Maximum rope size: 1/ 4". OD of sheave: 25/ 16". 41/ 2" overall length. TILLER ROPE PULLEY Item# Qty Case List 50-28601 2 12 5.99 PK For use with 1/ 8" or 3/ 16" rope. Chrome plated zinc. Dimensions: 11/ 4" x 11/ 16". TILLER ROPE CLAMP For 1/ 8" or 3/ 16" rope. The width is 11/ 16". Overall length is 11/ 4". TILLER ROPE CLAMPS Item# Finish Qty List 9-1226DP0CHR(K) Chrome Zinc 2 12.99 PK This die cast zinc, chrome plated wire rope clamp is used to secure 1/ 8" 3/ 16" diameter wire cable. CHROME PLATED ZINC CABLE CLAMP Item# A B C Qty List 354-0918521c(LK) 3/ 16" 13/ 16" 11/ 16" 2 6.80 PK 354-091852c 3/ 16" 13/ 16" 11/ 16" 1 2.75 EA Item# Length Compressed Qty List 354-091814c(K) 5" 6" 1 4.50 EA 354-0918141c 5" 6" 2 11.50 PK Electro-galvanized steel tiller rope springs provide tension between the tiller rope and jaw shackles. TILLER ROPE SPRINGS Item# Length List 241-51815a 250' 112.99 EA Clear vinyl coated tested to 1000 pound tensile strength. 7 x 7, 3/ 16" O.D., 3/ 32" Dia. DP TILLER CABLE Item# Shaft Size Length Keyway Size List 379-10TA10X700c(K) 1" 7" 91/ 2" 1/ 4" 171.29 EA 379-10TA12X700c(K) 11/ 4" 7" 91/ 2" 1/ 4" 199.29 EA 379-10TA12X900c(K) 11/ 4" 9" 111/ 2" 1/ 4" 266.29 EA Bolt & keyway type. Bronze. Note: Size is the maximum distance from the center of the shaft to the center of the connection point. TILLER ARM
RkJQdWJsaXNoZXIy MTI2MTky