GENERAL BOATING WATERSPORTS & BOATS SEATING COVERS/TOPS MAINTENANCE ELECTRICAL HARDWARE PLUMBING PROPS & ANODES FUEL ELECTRONICS & NAVIGATION SAFETY TROLLING & FISHING ANCHORING/ MOORING TRAILERING PAINT VENTILATION FASTENERS STEERING ENGINE ITEMS ARE STOCKED IN OUR WAREHOUSES BASED ON REGIONAL DEMAND. IF AN ITEM IS NOT IN STOCK AT A LOCAL WAREHOUSE, ADDITIONAL CHARGES MAY APPLY. u - WARNING Cancer Causing See www.P65Warnings.ca.gov v - WARNING Reproductive Harm w - WARNING Cancer and Reproductive Harm 1060 SECTION VENTILATION Radial flow design. Produces a substantial output at relatively low RPM's. Low noise level make excellent for use in heads & galleys. Massive 3" diameter motor idles at 3100 RPM's assuring long life. Housings are molded of tough glass filled composite resin. Flange Mount # 54124 - Conventional design outlet flange to mount directly to the exhaust opening in the hull. Molded mounting brackets simplify installations. Remote Mount # 54154 - 3" ducts attach to both the inlet and the outlet and readily adapt to new or existing vents and collector boxes. Brackets are molded in. Item# Type Hose CFM Volts Amps List 189-54124c Flange Mt. 3" 112 12 5 116.99 EA 189-54154c Remote Mt. 3" 112 12 5 116.99 EA 54124 54154 BILGE BLOWER Item# Hose CFM Volts Amps List 189-66302c 3" 158 12 3.5 54.89 EA 189-66402c 4" 240 12 3.5 56.89 EA • High efficiency blower • High capacity at low amp draw • Constructed of ABS plastic • Meets & exceeds: ABYC H-2 • NMMA Type Accepted, U.S.C.G. 33 CFR sections 183.410, 183.425 & 183.610 • 1 Year Warranty IN-LINE BLOWER 66302 66402 Item# Type Hose CFM Amps Size List 189-804741701c Flange Mt. 4" 324 12.5 11.5"H x 10"W x 6" 217.79 EA Extra heavy duty marine radial blower is designed for engine compartment ventilation prior to startup. Made for continuous duty and is therefore suitable for air intake or extraction in bilges, galleys, accommodation and other compartments. Flange Mount design with double ball bearing motor, high-impact anti-shock ABS body with stainless steel shaft and screws. 12V. AirV RADIAL BLOWER Item# Hose CFM Volts Amps Fuse Size List 29-140]a 3" 135 12 2.9 4A 53.99 EA 29-240]a 4" 235 12 4.3 7A 64.69 EA Provides ventilation for bilges, engine compartments, galleys and heads. Designed for efficient, high output operation. Easily installed on any flat surfaces. Sealed motor shaft for moisture protection. IN-LINE BLOWER 140 240 Hose and Cowl Vents Item# Color List 760-H5041B(W) Black 33.99 EA 3" Global directional euro louver vent with shut off vanes. Measures 3.9" diameter and 3" deep. EURO VENT Item# Size Hose Color Fastener List 354-3373161 311/ 16" x 311/ 16" Up to 3" White #8 FH 4.50 EA Flush Thru Vents are designed for cabin or bilge ventilation. Constructed of UV resistant injection molded ABS. For use with exhaust hose. Installs with four #8 FH fasteners (not included). Avoid contact with acetone or strong solvents. FLUSH HOSE VENT Hose Vent Elbows are constructed of impact resistant injection molded ABS. For use with 3" hose vents to create a 90° bend. HOSE VENT ELBOW Item# A B C D List 354-337350 23/ 4" 3" 213/ 16" 311/ 16" 10.45 EA Hose Thru Vents are designed for cabin or bilge ventilation. Constructed of UV resistant injection molded ABS. For use with 3" or 4" exhaust hose. Installs with four #8 FH fasteners (not included). Avoid contact with acetone or strong solvents. Item# A B C Hose Color List 354-337325 213/ 16" 27/ 16" 311/ 16" 3"/31/ 8" Black 4.60 EA 354-337315 213/ 16" 27/ 16" 311/ 16" 3"/31/ 8" White 5.00 EA 354-337415 39/ 16" 3" 45/ 16" 4" White 5.75 EA HOSE THRU VENT Black White Designed for cabin or bilge ventilation. Constructed of injection molded polypropylene they are UV resistant. For use with 3" exhaust hose. Installs with four #8 FH fasteners (not included). Vent area 3.04 square inches. Item# A B C Color List 354-337310c 213/ 16" 5/ 8" 311/ 16" White 2.50 EA THRU VENT
RkJQdWJsaXNoZXIy MTI2MTky