ITEMS ARE STOCKED IN OUR WAREHOUSES BASED ON REGIONAL DEMAND. IF AN ITEM IS NOT IN STOCK AT A LOCAL WAREHOUSE, ADDITIONAL CHARGES MAY APPLY. u - WARNING Cancer Causing See www.P65Warnings.ca.gov v - WARNING Reproductive Harm w - WARNING Cancer and Reproductive Harm AWNINGS & ACCESSORIES CAMPSITE LIVING GENERAL ACCESSORIES ROOFING & SEALANTS SANITATION HEATING & COOLING GRILLING & CAMPWARE HOUSEWARES CLEANERS & WAXES FRESH WATER APPLIANCES GENERATOR & POWER SOLUTIONS LIGHTING HARDWARE SERVICE & MAINTENANCE STEPS & TIEDOWNS TOWING & HITCHES ELECTRICAL ELECTRONICS VENTS CARRIERS & COVERS JACKS & LEVELERS LP GAS 442 ELECTRICAL Item# Type Amps List 240-31112c 90° Bracket 15 7.89 EA 240-31113c 90° Bracket 20 7.89 EA 240-31115c 90° Bracket 30 7.89 EA 240-31117c 90° Bracket 40 7.89 EA 240-31118c 90° Bracket 50 7.89 EA 240-31121c In-Line Bracket 10 7.89 EA 240-31122c In-Line Bracket 15 7.89 EA 240-31123c In-Line Bracket 20 7.89 EA 240-31125c In-Line Bracket 30 7.89 EA 240-31128c In-Line Bracket 50 7.59 EA 90° In-Line Designed to protect an electrical circuit from damage caused by overload or short circuit. Can be reset (either manually or automatically) to resume normal operation. • Comply with SAE Standard J553 • Auto Reset AUTO RESET CIRCUIT BREAKER W/BRACKET Designed to protect an electrical circuit from damage caused by overload or short circuit. Can be reset (either manually or automatically) to resume normal operation. AUTO RESET CIRCUIT BREAKER - BLADE STYLE Item# Amps List 240-31184c 30 8.79 EA AUTOMATIC RESET CIRCUIT BREAKER WITH BRACKET Item# Amps List 329-54220 20 5.19 EA 329-54230 30 5.09 EA 329-54240 40 4.89 EA Used in 6, 12 and 24V DC applications. Automotive, R.V., air conditioners, battery chargers, any application requiring overcurrent protection. Non-corrosive molded cover eliminates grounding when operating against a fault line. Includes mounting bracket and installed nuts and washers. CIRCUIT BREAKER Item# Amps List 220-7022ASc 50 13.69 EA • Quick connect clips allow circuit breakers to snap easily into place • Tin-plated copper busses and screw terminals • Clear insulating cover with square format label recesses, satisfies ABYC/USCG insulation requirements • Easy to open cover clip • Two breakouts for wire access • Accepts ring terminals • Optional push button waterproof boots or dress nuts can be installed over cover • Voltage Max 32V DC • Amperage Max 32A (per circuit) • Amperage Max 100A (per block-common source) • Amperage Max 40A (per jumped circuit groupindependent source) ST CLB PUSH BUTTON CIRCUIT BREAKER BLOCK 6 Circuit 12 Circuit Item# Description List 661-5052 6 circuit (w/neg bus) 84.19 EA 661-5054 12 circuit (w/neg bus) 144.19 EA Item# Description Size Amps List 267-ITEQ115c One Pole 2.56"H x 1"W x 2.88"L 15 18.79 EA 267-ITEQ120c One Pole 2.56"H x 1"W x 2.88"L 20 18.59 EA 267-ITEQ130c One Pole 2.56"H x 1"W x 2.88"L 30 18.59 EA 267-ITEQ1520c Two Pole, Duplex 15/20A 60.29 EA 267-ITEQ3020c Two Pole, Duplex 30/20A 49.39 EA Single Pole Twin Pole, Duplex HACR, SWD rated. 120VAC, 10,000 AIC. REPLACEMENT CIRCUIT BREAKERS Switched Solenoids Item# Volts Rating Replaces List 969-1002203c 12 65A CH 24059-08 48.99 EA 969-1002204c 12 85A CH 24059 42.49 EA Remotely switch high amperage loads with a low amperage on-off switch. • Copper #10-32 ignition and ground terminals • Copper 5/ 16"-24 contact terminals • Plated steel case, copper contacts • Hex nuts and washers included • Bracket mounting holes 5/ 16" x 19/ 32", 213/ 64" on centers • UL and CE approved CONTINUOUS DUTY SOLENOID Remotely switch high amperage loads with a low amperage on-off switch. • Intermittent rating 100A: 10 seconds • Copper #10-32 signal terminals • PVC coated steel case • Copper 5/ 16"-24 contact terminals • Bracket mounting holes 5/ 16" x 19/ 32", 2 13/ 64" on centers • UL and CE approved PVC COATED CONTINUOUS DUTY SOLENOID Item# Volts Rating Replaces List 969-1002205c 12 85A CH 24117-01 57.29 EA Item# Volts Replaces List 969-1002206c 6-12 CH M-200 37.19 EA Intermittent switching of high amperage loads with a low amperage on-off switch. • #10/32 signal terminals • Signal voltage 12V DC and contact voltage 6-12V DC • Copper 5/ 16"-24 contact terminals • Bracket mounting holes 5/ 16" x 19/ 32", 2 13/ 64" on center • Rated at 750A make/100A break, this solenoid is for intermittent use only: 10 seconds ON, 20 minutes OFF (ideal for engine cranking) INTERMITTENT DUTY SOLENOID Item# Volts Rating Replaces List 969-1002201c 12 75A CH 24450 84.19 EA Two solenoids in one saves money and simplifies wiring. Provides braking dynamic capability for permanent magnet motors when coils are not energized. • Rated at 75A make and break at 12V • DPDT intermittent duty • Comparable to Cole Hersee #24450 MOTOR REVERSING SOLENOID
RkJQdWJsaXNoZXIy MTI2MTky