GENERAL BOATING WATERSPORTS & bOATS SEATING COVERS/TOPS MAINTENANCE ELECTRICAL HARDWARE PLUMBING PROPS & aNODES FUEL ELECTRONICS & NAVIGATION SAFETY TROLLING & fISHING ANCHORING/ mOORING TRAILERING PAINT VENTILATION FASTENERS STEERING ENGINE Item Numbers in Red are hazardous items in blue are new ] sea value v oversized d ups/fedex Surcharge (L) = SE & MIDWEST only (K) = NE & Mid-ATLANTIC only (W) = WEST COAST only u - WARNING Cancer Causing See www.P65Warnings.ca.gov v - WARNING Reproductive Harm w - WARNING Cancer and Reproductive Harm 127 ELECTRONICS Item# Description Material List 167-QCMNw For Quick Connect antennas up to 4' White Nylon 63.29 EA 167-QCMSu For Quick Connect antennas up to 8' Stainless Steel 113.89 EA Versatile four-way ratchet action and fast-release handle design for quick and easy laydown. For deck or side mounting of QuickConnect® antennas. • Standard 1” -14 thread • Bolt holes: 9/ 32”, 3” x ½” on center • Water and dust protection cap, stays fastened to mount • PL-259 Connector & 20'RG-58 coax cable included To be used with QuickConnect® antennas only. QCM - QUICKCONNECT® RATCHET MOUNT Stainless Nylon Item# Description List 167-414u Shim Kit 14.99 EA Fits #4186 and 4187 5deg. Tilt contains 2-front-to-back and 2-side-to-side shims. SHIM KIT Item# List 236-GS8001] (LK) 729.99 EA Created specifically to prevent climbing on the boat gunnel to raise and lower a VHF antenna. Lift and descend the antenna from the safety of the deck from under the top. Its smooth operation, attractive machined aluminum frame and cast stainless-steel rotator make this item a must for any boater. • No climbing on T-tops or gunnels • Standard 1"-14 thread (male) • Machined / Anodized aluminum body • Light brushed finish • Polished Type-316L stainless folding crank handle • Delrin bearings for smooth operation • Roller bearings in crank assembly • Mounts on hardtops up to 2" thick • Includes 4" x 1/ 4" round backing plate (hardware not included) • Made in the USA • 1-year limited warranty GRAND SLAM VHF ANTENNA MOUNT GS8001 Adjust your antenna with the simple push of a button from the helm. A fully electric unit with hidden wires inside the hardtop. Easily installs to the surface of the hardtop and fits all top thicknesses. Item# List 236-GS850w (LK) 899.99 EA • Standard 1”-14 thread (male) shaft to accept standard antennas up to 8' • No under-mount clearance required • Machined / Anodized aluminum body with a light brushed finish • Consistent lift and descent • Delrin bearings for smooth operation • Features breakaway pin for manual operation • Includes 6" lead for 12VDC power • Requires a 7A fuse in power line GRAND SLAM ELECTRIC VHF ANTENNA MOUNT Antenna Clips Item# Size Pack Case List 50-72061 3/ 8" 4 12 10.89 PK 50-72071 5/ 8" 4 12 10.89 PK 50-72081 1" 2 12 10.89 PK White rubber, flexible fishing rod and tool holder. Larger size will accommodate boat hooks and boarding ladders. ANTENNA, ROD AND TOOL HOLDER 72081 72071 72061 Rail Mount Antenna Mounts Item# Material Case List 50-19561]w White Nylon 10 19.59 EA Fits rail tubing 7/ 8" or 1" and standard 1"-14 threaded antenna ferrules. NYLON ANTENNA RAIL MOUNT Item# Material Case List 50-19541]w 316 cast stainless steel 10 66.89 EA Mount fits both 7/ 8" and 1" rails and standard 1"-14 threaded antenna ferrules. STAINLESS STEEL ANTENNA RAIL MOUNT Item# Fits List 922-RA01 1" Rails 99.00 EA Includes a watertight seal for additional protection against exposure to the sea. Allows for internal cable routing for a neat installation. STAINLESS STEEL RAIL MOUNT Item# Fits List 354-3271411w (LK) 7/ 8"-1" Tubing 41.25 PK Constructed of corrosion resistant formed 304 stainless steel. Iincludes UV stabilized injection molded nylon mounting brackets for use on 7/ 8" and 1" tubing. Can be mounted on either vertical or horizontal rails as well as any flat surface. Design allows antenna wire to feed directly through the base. Not recommended for whips over 8’. RAIL MOUNT FIXED ANTENNA MOUNT Item# List 167-4190u (KW) 83.39 EA Designed for quick and easy installation on 7/ 8" and 1" vertical or horizontal rails. Handles up to 8' antennas and has feed-thru provision for cable. 4190 STAINLESS STEEL RAIL MOUNT Item# Material List 167-4188SLu Stainless steel 125.99 EA Swivel type ratchet action, fast release design for quick and easy laydown. Mounts easily on 7/ 8" to 1 1/ 2" vertical or horizontal rails. Handles antennas up to 8'. Standard 1"-14 thread. 9/ 32" hole for cable feed. RATCHET RAIL MOUNT
RkJQdWJsaXNoZXIy MTI2MTky