Item Numbers in Red are hazardous items in blue are new ] sea value v oversized d COURIER Surcharge GENERAL BOATING WATERSPORTS & bOATS SEATING COVERS/TOPS MAINTENANCE ELECTRICAL HARDWARE PLUMBING PROPS & aNODES FUEL ELECTRONICS & NAVIGATION SAFETY TROLLING & fISHING ANCHORING/ mOORING TRAILERING PAINT VENTILATION FASTENERS STEERING ENGINE 257 WATERSPORTS & bOATS Item# Type Description Capacity List 957-LEAVERSTDP Standard Port Side 85 lbs. 1332.49 ST 957-LEAVERSTDS Standard Starboard Side 85 lbs. 1332.49 ST 957-LEAVERM3P Model 3 Port Side 85 lbs. 1360.29 ST 957-LEAVERM3S Model 3 Starboard Side 85 lbs. 1360.29 ST Repl. Parts Description List 957-PINL Large Push Pin 94.89 EA 957-PINS Small Push Pin 105.59 EA Designed to be used with Weaver Snap Davits. It allows your outboard to remain upright while your inflatable is in the vertical position. The Weaver Leaver is made of rugged stainless steel and accommodates outboards that are mounted to pivot either to the port or starboard. 13" of clear transom is required. Will not work with motors that have power trim and tilt. These units are easily switched port to starboard. Standard: For transoms up to 4" down from the top of the tube. Model 3: For deep transoms up to 6" down from the top of the tube. Visit weaverindustries.com for Additional Info & Measurement Instructions WEAVER LEAVER Model 3 Standard Item# Description Capacity List 957-HOISTLEAVER Manual Foot Operated 400 lbs. 5792.39 EA Pick up your dinghy and motor at the same time using our foot operated or 12V hydraulic hoist. Lifting from the Leaver bracket that your dinghy motor is attached to, the dinghy raises at the same time as the motor is swinging out over the swim platform. After the dinghy and motor are brought into the vertical position, the hoist remains hooked up to the dinghy/motor. For hard bottom dinghies. You will need to order the HDRBD202 davit system (not included) and at least one stand-off bracket at the bow of the inflatable for more stabilization. HD-RBD202 required for hoist/ leaver installation, sold separately. Weaver worksheet must be filled out as this product is custom tailored. Visit weaverindustries.com for Additional Info & Measurement Instructions HOIST/LEAVER Item# Pack List 957-QUICK 2 248.99 ST Repl. Parts Description List 957-PIN&LANYARD Replacement Pin & Lanyard 15.29 EA QUICK KIT Receiver plates for easy removal of the Davit Heads from the swim platform for use with the RBD100 and SSHR for the SD1. Comes with all the mounting hardware plus the pin and lanyard. Not to be used with RS150 Item# Type Mount Length Pack List 957-SO12 Fixed Clip on 1 End 12" 1 pr. 206.09 ST 957-SO18 Fixed Clip on 1 End 18" 225.79 ST 957-SO24 Fixed Clip on 1 End 24" 245.59 ST 957-SO30 Fixed Clip on 1 End 30" 267.59 ST 957-SO30CBE Fixed Clips on Both Ends 30" 312.59 ST 957-SO36 Fixed Clip on 1 End 36" 289.49 ST 957-SO36CBE Fixed Clips on Both Ends 36" 334.69 ST 957-SO60CBE Fixed Clips on Both Ends 60" 515.29 ST 957-SOA1218 Adj. Clip on 1 End 12"-18" 295.39 ST 957-SOA1218CBE Adj. Clips on Both Ends 12"-18" 340.49 ST 957-SOA1824 Adj. Clip on 1 End 18"-24" 314.89 ST 957-SOA1824CBE Adj. Clips on Both Ends 18"-24" 360.19 ST 957-SOA2430 Adj. Clip on 1 End 24"-30" 333.49 ST 957-SOA2430CBE Adj. Clips on Both Ends 24"-30" 378.69 ST 957-SOA3036 Adj. Clip on 1 End 30"-36" 356.69 ST 957-SOA3036CBE Adj. Clips on Both Ends 30"-36" 401.89 ST 957-SOA3642 Adj. Clip on 1 End 36"-42" 378.69 ST 957-SOA3642CBE Adj. Clips on Both Ends 36"-42" 423.79 ST 957-SOA4248 Adj. Clip on 1 End 42"-48" 423.69 ST 957-SOA4248CBE Adj. Clips on Both Ends 42"-48" 468.99 ST 957-SOA4854 Adj. Clip on 1 End 48"-54" 468.99 ST 957-SOA4854CBE Adj. Clips on Both Ends 48"-54" 514.09 ST 957-SOA5460CBE Adj. Clips on Both Ends 54"-60" 559.29 ST Repl. Parts Description List 957-LCLIP "L" Brackets for Standoffs, 4-Pack 31.39 PK • For hard shelled and inflatable boats • Pivot back to the boat transom and clip neatly in place • 100% solid stainless steel • Spring-loaded thumb clip for one hand operation • Recommended for any davit system CBE Standoffs: Quick disconnect clips on both ends. When stand-offs are not in use they can be taken off and stowed. Sold in pairs. STAND-OFF BRACKETS Clip Both Ends Clip 1 End Item# Color List 957-RP301 Black 53.39 EA 957-RP301G Grey 53.39 EA 957-RP304G Grey w/swivel 68.49 EA This hypalon, molded rubber pad is used to clip stand-offs to inflatable boats. STAND-OFF PAD Grey Black Item# Type Color Size List 957-WR1G Standard Grey 1" 49.89 EA 957-WR112 Standard Black 1 1/ 2" 64.89 EA 957-WR112G Standard Grey 1 1/ 2" 64.89 EA 957-WR2 Standard Black 2" 114.79 EA 957-WR2G Standard Grey 2" 114.79 EA 957-WR112S Swivel Black 1 1/ 2" 79.99 EA 957-WR112SG Swivel Grey 1 1/ 2" 79.99 EA 957-WR2SG Swivel Grey 2" 127.39 EA The Weaver mounting rings come in two models, standard or swivel. Available in three sizes 1", 1 1/ 2" and 2" stainless steel ring size. MOUNTING RING Black Grey
RkJQdWJsaXNoZXIy MTI2MTky