GENERAL BOATING WATERSPORTS & bOATS SEATING COVERS/TOPS MAINTENANCE ELECTRICAL HARDWARE PLUMBING PROPS & aNODES FUEL ELECTRONICS & NAVIGATION SAFETY TROLLING & fISHING ANCHORING/ mOORING TRAILERING PAINT VENTILATION FASTENERS STEERING ENGINE Items are stocked in our w arehouses based on reg ional demand. If an item is not in stock a t a local w arehouse, add it ional charges ma y appl y. u - WARNING Cancer Causing See www.P65Warnings.ca.gov v - WARNING Reproductive Harm w - WARNING Cancer and Reproductive Harm ENGINE 1382 Item# Rating List 119-52100w (LK) Up to 35hp 826.39 EA Repl. Parts Description List 119-52060w (L) Bottom clevis bracket 38.29 EA • 5 1/2" Set Back enhances stability & performance • 84° Trim & Tilt • 1/4" 6061 T6 Extruded aluminum w/SS Fasteners • Actuator rated at 7853 lbs. of thrust • For clamp-on or bolt-on motors w/o adapter. Mounting bolts NOT included • Only 24lbs. The maximum width of the clamp mounting feet and/or mounting bolts of the motor must not exceed 11". PT-35 ELECTRIC HYDRAULIC TILT & TRIM Item# Description Rating List 781-550035 Model 35 Auxiliary O/B Motor Lift Up to 35hp/150 lbs. 750.29 EA Opt. Accy. Description List 781-559035 (LW) 3" Spacer Kit 144.59 EA 781-551200 (LW) Push Button Trim Switch 48.79 EA 12V power driven actuator includes 12' of cable with a push button up/down control. The unique convertible setback allows you to adjust it for 7 or 13 inches of setback, making it ideal for virtually all applications. 3" spacer kit: 2-piece, cast aluminum, provides an extra 3" of setback to allow most kicker motors to be tilted up without hitting transom. By MarineTech TM MOTOR TILT/LIFT Item# List 781-550055 752.49 EA Opt. Accy. Description List 781-551200 (LW) Push Button Trim Switch 48.79 EA Designed for pontoons, fishing, or pleasure boats. Compact, handles outboards from 15 to 55hp weighing up to 250 pounds. Provides an additional five degrees of negative tuck for improved hole shot. Adapts to clamp-on or bolt-through outboards. By MarineTech TM STANDARD TRIM & TILT Item# Rating List 781-550135 Up to 135hp / 350 lbs. 1099.89 EA Opt. Accy. Description List 781-551200 (LW) Push Button Trim Switch 48.79 EA Maximizes lifting power (even greater than the outboard's tilt range). Also allows for increased tuck-under to get heavy boats on plane quickly. An ideal option for older outboards with bad hydraulic trim and tilts, when repair costs are expensive. Optional push button trim switch available. By MarineTech TM HEAVY DUTY TRIM & TILT Item# List 781-559000 (W) 38.99 EA This sacrificial anode for all Panther trim & tilts when used in salt or brackish water. Mounting bolt supplied. By MarineTech TM SALTWATER ANODE KIT Item# List 781-551500 (L) 9.69 EA Fits any auxiliary outboard with a Panther Model 35 lift. As the engine is tilted, the strap tightens, and secures the motor for rough water conditions. As the motor is lowered, the two-inch driving belt strap stays secured and tucks to the side. Adjustable buckles and stainless clevis are included. One per package. By MarineTech TM PRO KICKER TIE DOWN STRAP Item# Description List 119-52060w (L) Bottom clevis bracket 38.29 EA Bottom Clevis Bracket TH-CMC. BOTTOM CLEVIS BRACKET Transom Wedges Designed to give extra positive or negative trim. 1/2" x 4" x 11 1/4". Item# Pack List 119-20122w 2 92.89 EA • Used as an aid for boats with an insufficient transom angle or for boats having planing problems at low speed • Unique design allows you to also use them as set back spacers, simply stack and invert 2, 4, or 6 sets • Fit all transom jacks, jack plates, outboard lifts, tilt trim units, and motors with a standard B.I.A bolt pattern • Made of strong 6061 T6 alloy aluminum (not cast aluminum) 2° CMC TRANSOM WEDGES/SET BACK SPACERS Jack Plates Item# Model Setback Rating List 651-1001060d (L) Flats Jac 6" 300hp / 625lbs. 1530.89 EA 651-1001100 (L) Max. Jac 10" 300hp / 625lbs. 1716.49 EA • Includes: jac plate, pump, wire harness, 7’ hoses, control switch & oil • Remote mount pump • Transom side mounting dimensions: 16 3/4”W x 13 3/4”H • Motor side mounting dimensions: 18 1/4”W • All jac plates provide 7.5” of lift • Limited lifetime warranty on structure, 5 years on pump • “Predrilled” for side mount Shallow Water Anchors • Less weight on transom, pump stays dry in internal location STANDARD JAC™ PLATE 1001100 1001060 Item# Setback List 651-100106010 (LK) 6" 1577.19 EA 651-100108001w (L) 8" 1353.69 EA 651-100111000w (LK) 10" 1400.39 EA 651-100112112w (L) 12" 1447.49 EA 651-100114001dw (L) 14" 1586.99 EA • Internal pump inside plate for easier rigging • One piece jac plate - No C-Channels to bolt on • Powerful motor can lift heavy outboards under full power in 6 seconds • Limited lifetime warranty against structural defects • Can be converted to have pump inside the boat • Predrilled for side mount Shallow Water Anchors • Provides 7.5” (19 cm) of lift • Plug and play with waterproof Deutch® connectors • Rated for up to 300hp / 625 lbs ACTION SERIES JAC™ PLATE Item# Setback List 651-100606005w (L) 6" 1702.69 EA 651-100608005w (L) 8" 1669.29 EA 651-100610005dw (L) 10" 1795.29 EA 651-100612005dw (L) 12" 1841.99 EA Action pump is built into the jack plate making rigging the boat extremely easy. Jack plates are no longer just for fishing boats, offshore boaters will enjoy the extra speed and increased fuel economy. Improves an outboard boat's speed, holeshot, fuel efficiency, and shallow water navigation. • Action Pump built into plate for ease of rigging • Rated to 550HP • For Yamaha 425hp motors, use of 1” spacers required EXTREME GEN 3 ACTION JAC™ PLATE
RkJQdWJsaXNoZXIy MTI2MTky